Legrand RC7APTCGY User Manual download pdf

IMPORTANT – PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.

Products Covered: RC7STC, RC7ATC, RC7ATJTC, RC7CTC, RC7CTJTC, and RC7SHTC

RC7ATC-LJB, RC7ATJTC-LJB, RC7ATCLJB25 and RC7ATJTCLJB25

CAUTION: Do Not operate tile stripper or resurfacing equipment over top of covers. This may result in damage to the surface finish of the product.

Suitable for use in air handling spaces in accordance with Sec. 300-22 (C) of the National Electrical Code.

Step 1. Layout and locate position of hole(s). Step 2. Remove 6 1/2" [165mm] section from carpet

or tile. Use template provided.

CAUTION: Holes shall be spaced a minimum of 2' [610mm]

on center and not more than one hole per each

65 sq. ft. [6 sq. m] of floor area in each span.

For Tile Applications up to a Maximum of 3/4" [19.1mm] Thick.

NOTE: Be certain to drill hole at least 4" [102mm] from any wall NOTE: For tile thickness greater than 3/4" [19.1mm] consult factory.

or pillar to leave enough room for Poke-Thru cover assembly.

Step 3. Core drill hole. Step 4. Stem Assembly: Step 5. Cover Assembly:

Catalog No. RC7STC. Catalog No. RC7CTC

Insert stem into hole. or RC7CTJTC. Remove

disposable plate and replace

with carpet/tile flange. Install

with four #6-32 x 1/4"

[6.4mm] FHMS.

24" [610mm] Min

Center – Center

6 1/2"

[165mm] Diameter

CAUTION: Poke-Thru cannot be rotated

in hole after insertion into floor.

3" Diameter Core Drill

3 1/16" [78mm] Actual Diameter

Push Down

Four #6-32

x 1/4" FHMS

Poke-Thru Series

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 1 001 628 R2 – Updated April 2005

Wiremold Electrical Systems conform to and should be installed

and properly grounded in compliance with requirements of the

current National Electrical Code, Canadian Electrical Code or

codes administered by local authorities.

All electrical products may represent possible shock or fire hazard

if improperly installed or used. Wiremold electrical products are

UL Listed to U.S. and Canadian safety standards, made for

interior use only, and should be installed in conformance with

current local and/or the National Electrical Code.

1 2 3 4 5 6

Summary of Contents

Page 1 - Poke-Thru Series

IMPORTANT – PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING.Products Covered: RC7STC, RC7ATC, RC7ATJTC, RC7CTC, RC7CTJTC, and RC7SHTC RC7ATC-LJB, RC7ATJ

Page 2

Complete Assembly:Step 6. Cat. Nos. RC7ATC or RC7ATJTC Step 7. Wire the power circuit. Wire the Poke-Thru device. (Can be completed above floor.)Refe

Page 3

3Step 10. Wire and snap communication Step 11. For cable pass-through or empty jacks in adapters as shown. communication port, install foam block in

Page 4

4Step 14. Attach slide cover with two #6-32 screws. Step 15. Push Poke-Thru unit into concrete Pass-through cabling must pass through to complete in

Page 5

The RC7TC Series Poke-Thru Device is UL Listed and Classified to U.S. and Canadian safety standards to the following conditions: The RC7STC Poke-Thru

Page 6 - Carpet Cutout Template

Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6

Related models: RC7APTCBK | BZTPP Series | RC3APTCBK | RC3APTCGY | RC4KTCBK | RC4KTCGY | RC4KTCVY | RC4KTCAL | RC4KTCBS | RC4KTCAB | RC9 Poke-Thru Series |

Comments to this Manuals

No comments

Legrand RC7APTCGY User Manual

Browse online or download User Manual for Hardware Legrand RC7APTCGY. Legrand RC7APTCGY User Manual

Summary of Contents

Related models: RC7APTCBK | BZTPP Series | RC3APTCBK | RC3APTCGY | RC4KTCBK | RC4KTCGY | RC4KTCVY | RC4KTCAL | RC4KTCBS | RC4KTCAB | RC9 Poke-Thru Series |

Comments to this Manuals

Related products and manuals for Hardware Legrand RC7APTCGY