Legrand T600EI User Manual download pdf

Read and save these instructions

Wiring and Installation Diagrams Below

For Use with Models: T600E, T1000E

CAUTION

To avoid overheating and possible damage to equipment do not install this device to control a

receptacle, a fluorescent lighting fixture, a motor operated appliance, or a transformer-supplied

appliance.

Notice: Use only copper wire with these devices.

This control is intended for installation in a UL-Listed metal or plastic (polymeric) outlet box.

INSTALLATION

1. Disconnect power to circuit by removing fuse or turning circuit breakers to OFF before installing.

2. Remove existing wall plate and switch.

3. Strip wires to 1/2" for size 14 or bigger, 5/8" for 16 or smaller.

4. Install dimmer as shown with wire connectors provided.

5. Replace dimmer in wall box.

6. Replace wall plate.

7. Place toggle in the OFF position before restoring power to circuit.

MAXIMUM LOAD PER DIMMER FOR MULTI-GANG

CAT. NO. SINGLE 2-GANG More than 2-GANG

T600E 600W 500W 400W

T1000E 1000W 800W 700W

OPERATION

1. To turn ON:

Single Pole: Flip toggle up.

3-Way: Flip toggle up or down until LED goes OFF and/or light turns ON.

2. Touch upper or lower touch pad to adjust lighting level.

3. To turn OFF:

Single Pole: Flip toggle down.

3-Way: Flip toggle up or down until LED goes ON and/or light turns OFF.

WIRING DIAGRAMS

Dimmer Parts Diagram Wiring Diagram

Single Control Application

Two Location Control Application

Three Location Control Application

CAUTION

In 3-Way Application, dimmer should be wired directly to load as shipped from the factory (small toggle

switch on back of device in UP position). To wire directly to line, flip small toggle switch on back of

device to DOWN position.

NOTE

Control may feel warm to the touch in normal operation

LIMITED THREE YEAR WARRANTY

Pass & Seymour will remedy any defect in workmanship or material in Pass & Seymour products which

may develop under proper and normal use within three years from date of purchase by a consumer:

(1) by repair or replacement, or, at Pass & Seymourʼs option, (2) by return of an amount equal to

consumerʼs purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy

by Pass & Seymour does not include or cover cost of labor for removal or reinstallation of the product.

ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES)

FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE

EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or

consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY

IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE THREE YEARS PERIOD SET

FORTH ABOVE. (Some states do not allow limitations on how long an implied warranty lasts, so the

above limitation may not apply to you.)

To insure safety, all repairs to Pass & Seymour products must be made by Pass & Seymour, or under its

specific direction. Procedure to obtain performance of any warranty obligation is as follows: (1) Contact

Pass & Seymour, Syracuse, New York 13221, for instructions concerning return or repair; (2) return the

product to Pass & Seymour, postage paid, with your name and address and a written description of the

installation or use of the Pass & Seymour product, and the observed defects or failure to operate, or other

claimed basis for dissatisfaction.

This warranty gives you specific legal rights and you may also have other rights which vary from state to

state.

This product is covered by one or more of the following U.S. Patents: 4,413,211; 4,430,576; 4,465,956;

4,733,138; 4,792,731; 4,871,893; 4.880,950; 4,988,840; 4,992,709; 5,128,654; 5,189,259; 5,194,858;

and DES 333,124. Other Patents Pending.

We reserve the right to change details of design, materials and finish, in any way that will not alter

installed appearance or reduce function performance.

Lire et conserver ces instructions.

Schémas de câblage et dʼinstallation ci-dessous

Pour utilisation avec les modèles : T600E, T1000E

ATTENTION

Pour éviter toute surchauffe et endommagement éventuel de lʼéquipement, ne pas installer ce dispositif

pour contrôler une prise, un tube fluorescent ou un appareil ménager équipé dʼun moteur

ou alimenté par un transformateur.

AVIS : Nʼutiliser que des fils en cuivre avec ces dispositifs.

Ce contrôleur est conçu pour être installé dans une boîte électrique en métal ou en plastique

(polymère) homologuée par UL.

Installation

1. Couper lʼalimentation du circuit en retirant le fusible ou en ouvrant les disjoncteurs avant

de commencer lʼinstallation.

2. Retirer la plaque murale et lʼinterrupteur existants.

3. Dénuder les fils sur 13 mm (1/2 po) pour les fils de calibre 14 ou plus, ou 16 mm (5/8 po)

pour les fils de calibre 16 ou moins.

4. Installer le gradateur comme illustré en utilisant les connecteurs fournis.

5. Installer le gradateur dans la boîte murale.

6. Remonter la plaque murale.

7. Placer lʼinterrupteur en position ARRÊT avant de remettre le circuit sous tension.

CHARGE MAXIMALE PAR GRADATEUR POUR INSTALLATION MULTIPLE

N° CAT. SIMPLE DOUBLE Plus de DEUX

T600E 600W 500W 400W

T1000E 1000W 800W 700W

FONCTIONNEMENT

1. Pour allumer :

Unipolaire : Mettre la bascule en position haute.

Tripolaire : Mettre la bascule en position haute ou basse pour que la DEL sʼéteigne et/ou que

la lumière sʼallume.

2. Effleurer la plaque tactile supérieure ou inférieure pour ajuster lʼintensité lumineuse.

3. Pour éteindre :

Unipolaire : Mettre la bascule en position basse.

Tripolaire : Mettre la bascule en position haute ou basse pour que la DEL sʼallume et/ou que

la lumière sʼéteigne.

SCHÉMAS DE CÂBLAGE

Schéma des pièces du gradateur Schéma de câblage

Contrôle à partir

dʼun seul emplacement

NEUTRAL (WHITE)

HOT

TO LIGHT

BLUE

BLACK

RED

P.O. Box 4822, Syracuse, NY 13221 www.passandseymour.com Technical Support / Support technique (800) 223-4185

600W & 1000W Electronic Toggle Dimmers

INSTALLATION & OPERATING INSTRUCTIONS

Part No. 340559 Rev. D 85-1206

Gradateurs électroniques à bascule de 600 et 1000 W

INSTRUCTIONS DʼINSTALLATION ET DʼUTILISATION

Pièce n° 340559 Rév. D 85-1206

ON/OFF

Toggle

Upper Touch

Pad

LED

Lower Touch

Pad

120VAC 60 HZ

NEUTRAL (WHITE)

RED

DIMMER

WHITE

LOAD

BLACK

HOT (BLACK)

BLUE

GREEN

GROUND

WHITE

LOAD

BLACK

RED

DIMMER

BLACK

BLUE

GREEN

GROUND

RED

DIMMER

BLACK

BLUE

GREEN

GROUND

WHITE

LOAD

BLACK

GREEN

GROUND

GREEN

GROUND

GREEN

GROUND

4-WAY SWITCH

3-WAY SWITCH

120VAC 60 HZ

NEUTRAL (WHITE)

HOT (BLACK)

120VAC 60 HZ

NEUTRAL (WHITE)

HOT (BLACK)

COMMON

TERMINAL

(Black Screw)

COMMON

TERMINAL

(Black Screw)

Travelers between switches “IN”

Travelers between switches “OUT”

Plaque tactile

supérieure

DEL

Plaque tactile

inférieure

120 VCA 60 HZ

NEUTRE (BLANC)

ROUGE

GRADATEUR

BLANC

CHARGE

NOIR

PHASE (NOIR)

BLEU

VERT

TERRE

NEUTRE (BLANC)

PHASE

VERS LʼAMPOULE

BLEU

NOIR

ROUGE

1 2

NEUTRO (BLANCO) 2
A LA LUZ 2

Summary of Contents

Page 1

Read and save these instructionsWiring and Installation Diagrams BelowFor Use with Models: T600E, T1000ECAUTIONTo avoid overheating and possible damag

Page 2 - A LA LUZ

P.O. Box 4822, Syracuse, NY 13221 www.passandseymour.com Support technique / Asistencia técnica (800) 223-4185Contrôle à partir de deux emplacementsCo

Related models: T1000EI | T600ELA | T1000ELA | T1000EW | T600EW |

Comments to this Manuals

No comments

Legrand T600EI User Manual

Browse online or download User Manual for Hardware Legrand T600EI. Legrand T600EI User Manual

Summary of Contents

Related models: T1000EI | T600ELA | T1000ELA | T1000EW | T600EW |

Comments to this Manuals

Related products and manuals for Hardware Legrand T600EI