Legrand ALDS4000 Designer Series Large Raceway Base User Manual download pdf

ALDS4000 Raceway

Base & Cover

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 43371R1 – Updated August 2007

Wiremold / Legrand Electrical Systems conform to and should be

installed and properly grounded in compliance with requirements

of the current National Electrical Code, Canadian Electrical

Code, or codes administered by local authorities.

All electrical products may represent possible shock or fire

hazard if improperly installed or used. Wiremold electrical

products are UL listed to U.S. and Canadian safety

standards, made for interior use only, and should be installed

in conformance with current local and/or the National

Electrical Code.

Step 1. If the installation requires Fittings, start at an

appropriate location such as a corner. Refer

to specific fitting installation instructions for

proper mounting. Attach Adjust-to-Fit

™

Couplings to Fittings and tighten.

Step 3. Butt succeeding ALDS4000B Sections to the

installed Base Section and mount using the

same method as in Step 2.

Step 4. Install the next Fitting. Place an ALDS4000B Base Section

in line with the last piece of Base that was mounted. Mark

where the Base lines up with the Fitting and cut at this

point. Precise cuts are not required since the Adjust-to-

Fit

™

Coupling will maintain the integrity of the Base where

there are any gaps between Sections. Adjust-to-Fit™

Coupling can span gaps up to 4" [102mm].

Products Covered: ALDS4000B, ALDS4000C.

Step 2. Slide ALDS4000B Base Section onto Couplings and

tighten Screws. Drill a hole in each Channel of the Base

at the first Stud to secure to the Wall using a #8 Fastener.

Secure to Wall no more than 48" [1.2m] apart.

For more information, visit www.wiremold.com/ds4000.

Stud Location

NOTE: ALDS4000B Raceway Base includes Couplings and Wire Clips.

Wire Clips are factory installed in the lower Channel of each

Raceway Base Section. Make sure Base Sections are properly

oriented prior to securing to the Wall

NOTE: For backfeeding raceway, a hole may be drilled into either channel

of ALDS4000B to connect 1 1/4 trade size or smaller conduit.

1 2 3 4

Summary of Contents

Page 1 - Base & Cover

ALDS4000 Raceway Base & CoverINSTALLATION INSTRUCTIONSInstallation Instruction No.: 43371R1 – Updated August 2007Wiremold / Legrand Electrical S

Page 2 - ALDS4000C COVER REMOVAL:

Wire Clip Installation – Additional Wire Clips are provided for the upper Channel of the Raceway.ALDS4000C COVER INSTALLATION:Step 1.Step 2.ALDS4000C

Page 3 - Installation Complete

ALDS4006 SEAM CLIP INSTALLATION (optional):Step 1.Step 2.The ALDS4006 Seam Clip is used to cover the cut edge of aALDS4000C Cover Section. Make sure a

Page 4

Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6

Comments to this Manuals

No comments

Legrand ALDS4000 Designer Series Large Raceway Base User Manual

Browse online or download User Manual for Hardware Legrand ALDS4000 Designer Series Large Raceway Base. Legrand ALDS4000 Designer Series Large Raceway Base User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Legrand ALDS4000 Designer Series Large Raceway Base