Legrand DA1008 User Manual download pdf

INSTRUCTION / INSTALLATION SHEET

8-Port Gigabit Switch (DA1008)

IS-0396 Rev. B

301Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.legrand.us

1. INTRODUCTION

Legrand offers an 8-Port Gigabit Ethernet Switch (see Figure 1)

which comes with eight independent 1000Mbps ports. The

DA1008 switch is designed to easily install in an On-Q style

enclosure and its eight ports provides adequate capacity for

most homes. Each port can transmit at speeds up to 1000Mbps

in full duplex mode. The switch features a 16Gbps non-blocking

switch fabric as well as an 8K MAC Address table. It supports

802.3x full duplex flow control and offers wire-speed packet

transfer performance without packet loss. The Gigabit ports with

9K jumbo packet support can handle extremely large amounts of

data transmission in a secure topology linking to a backbone of

high-power servers. The switch is powered by a 12VDC, 18W

power supply (P/N PW7760, purchased separately).

2. DESCRIPTION

The Legrand 8-Port Gigabit Ethernet Switch has a power LED which lights green to indicate power is

supplied, and two green LEDs per port. The “1000” LED lights to indicate that port is running at 1000Mbps. If

it is off, it indicates that port is running at 10Mbps or 100Mbps. The “LNK/ACT” LED lights to indicate a

connection to an active device, and blinks when transmitting or receiving data. The switch complies with IEEE

802.3/3u/3ab/3x and 3az standards for Ethernet/Fast Ethernet/Gigabit Ethernet, full-duplex flow control and

Energy Efficient Ethernet (EEE). The switch will operate properly in humidity up to 90% and at a temperature

of 0-50 degrees C. It is a two bay module that comes with a two bay bracket (P/N 364819-01) for mounting in

an On-Q style enclosure.

3. INSTALLATION

A. Attach the 8-Port Gigabit Ethernet Switch to the supplied bracket using the pushpins in each corner and

position the switch in the enclosure, planning for wire management and location of additional modules.

B. Align two stationary tabs on the bracket with slots on the back of the enclosure.

C. Insert tabs by angling module away from the back of the enclosure and sliding forward.

D. Rotate the module and insert the built in locking tab/s on the module into the corresponding hole/s on the

back of the enclosure, pushing in until it snaps into place.

E. Pull lightly on the module to assure it is properly locked in place.

F. Plug the DC power supply into the switch and an appropriate AC outlet inside the Enclosure.

G. Verify that the Power LED is illuminated. If it isn’t illuminated, then check the connections, power supply

and 110 VAC source. If still not illuminated, contact Legrand Technical Support at 1-800-321-2343.

H. The DA1008 8-Port Gigabit Ethernet Switch is considered a “plug and play” network device and requires

no special setup. Since the switch employs auto-crossover technology, Ethernet cables that are “straight-

through” or “crossover” design will work for all applications.

I. As each active device is plugged into a switch port, verify that the “LNK/ACT” LED is illuminated for that

port. The “1000” LED may also be lit if the device attached to the port is running at 1000Mbps. If the

“LNK/ACT” LED does not light for an active device, check its Ethernet cable or the device itself.

The 8-Port Gigabit Switch may be used by itself to create a large local PC network or with a router to expand

the router’s port count (see Figure 2).

Figure 1

1 2 3 4 5 6

IS-0396 Rev. B 1

Summary of Contents

Page 1 - IS-0396 Rev. B

INSTRUCTION / INSTALLATION SHEET 8-Port Gigabit Switch (DA1008) IS-0396 Rev. B 301Fulling Mill Road, Suite G Middletown, PA 17057 Phone (800) 321-23

Page 2

INSTRUCTION / INSTALLATION SHEET 8-Port Gigabit Switch (DA1008) IS-0396 Rev. B 301Fulling Mill Road, Suite G Middletown, PA 17057 Phone (800) 321-23

Page 3

FEUILLE D'INSTRUCTION / D'INSTALLATION Commutateur Gigabit à 8 ports (DA1008) IS-0396 Rev. B 301Fulling Mill Road, Suite G Middletown, PA

Page 4

FEUILLE D'INSTRUCTION / D'INSTALLATION Commutateur Gigabit à 8 ports (DA1008) IS-0396 Rev. B 301Fulling Mill Road, Suite G Middletown, PA

Page 5

HOJA DE INSTRUCCIONES/INSTALACIÓN Interruptor Gigabit de 8 puertos (DA1008) IS-0396 Rev. B 301Fulling Mill Road, Suite G Middletown, PA 17057 Phone

Page 6

HOJA DE INSTRUCCIONES/INSTALACIÓN Interruptor Gigabit de 8 puertos (DA1008) IS-0396 Rev. B 301Fulling Mill Road, Suite G Middletown, PA 17057 Phone

Comments to this Manuals

No comments

Legrand DA1008 User Manual

Browse online or download User Manual for Hardware Legrand DA1008. Legrand DA1008 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Legrand DA1008