Legrand RW600U User Manual download pdf

No: 341002 – 3/13

Pass & Seymour

Occupancy/Vacancy Sensor Switch

Interrupteur à détection de présence/Interrupteur détecteur d’inoccupation

Interruptor de sensibilidad a la ocupación/Interruptor con sensor de “habitación vacía”

Incandescent/ELV: 600; CFL/LED: 450; MLV: 600VA; ELV: 5A; Motor: 1/6 hp

Installation Instructions • Notice d’Installation • Instrucciones de Instalación

Catalog Number(s) • Numéro(s) de Catalogue • Les Numéros de Catalogue: RW600U

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

DESCRIPTION AND OPERATION

The R600U occupancy and vacancy Sensor is designed to replace a

standard light or fan switch. The sensor uses passive infrared technology

to sense human motion in a space and turn the light OFF when the room

is vacant. It is ideal for applications in a home where there is a direct line

of sight from the sensor to the room, including bedrooms and family/living

rooms.

Occupancy Mode:

The load will automatically come ON when motion is detected, and turn

OFF automatically, at the desired time delay, if no motion is detected. If the

load is manually turned OFF, and motion is detected within 30 seconds,

the load will remain OFF until no motion has been detected for 30 seconds.

It can then automatically turn ON again once it detects motion. The

R600U allows the load to be turned ON manually as well, and turn OFF

automatically at the desired time delay, if no motion is detected.

Vacancy Mode:

In this mode, the load is required to be turned ON manually, and will

turn OFF at the desired time delay, if no motion is detected. If motion is

detected within 30 seconds after it automatically turns OFF, the R600U

automatically turns the load back ON.

INDICATOR LED

The R600U also has an onboard indicator LED e

mbedded in the

pushbutton switch. This indicator is used to show when motion is

detected. The LED is also used while programming the R600U and

indicates STATUS during power up. The LED is further used to indicate

a malfunctioning unit. Both Occupancy and Vacancy modes can be

programmed/selected to function with or without the LED indicator if

preferred by the user.

Table 1

Setting Status From User (Input to the

device)

LED or LOAD State

(Acknowledgement

from the device)

Result

Programming

Mode

Initiate

With the load ON or OFF,

hold down the ON/OFF

button for 5 sec.

LED will blink 5 times

and then turn off

Enters

Programming

Mode

Activate

Push down the ON/OFF

button first time.

LED flashes quickly one

time ON per 1s,

Enters Occupancy

mode

Push down the ON/OFF

button second time.

LED flashes quickly

two times ON per 1s,

Enters Vacancy

Mode

Push down the ON/OFF

button third time.

LED flashes quickly

three times ON per 1s,

Enters Occupancy

Mode with Disable

LED

Push down the ON/OFF

button fourth time.

LED flashes quickly four

times ON per 1s,

Enters Vacancy

Mode with Disable

LED

Save/Exit

Hold down the ON/OFF

button for 5 seconds.

LED will blink 5 times

and then turn off

Save/Exit

Programming

Mode

Table 2

Setting Status Functional description

Load

status

LED

performance

Operation

Occupancy

Mode

Load turns ON when motion is detected.

Load may also be

turned ON manually.

ON LED will blink as

motion is detected

Load turns OFF after set time, if no

motion is detected. Load may also be

turned OFF manually with ON/OFF

button.

OFF LED will blink as

motion is detected

Vacancy

Mode

Load turns ON when ON/OFF button

is pressed.

ON LED will blink as

motion is detected

Load turns OFF after set time, if no

motion is detected. Load may also be

turned off manually with ON/OFF button.

OFF LED will blink as

motion is detected

Occupancy

Mode with

LED disabled

Load turns ON when motion is detected.

Load may also be turned ON manually.

ON LED will not

turn on.

Load turns OFF after set time, if no

motion is detected. Load may also be

turned OFF manually with ON/OFF

button.

OFF LED will not

turn on.

Vacancy

Mode with

LED disabled

Load turns ON when ON/OFF button

is pressed.

ON LED will not

turn on.

Load turns OFF after set time, if no

motion is detected. Load may also be

turned off manually with ON/OFF button.

OFF LED will not

turn on.

COVERAGE AREA

The R600U has a maximum coverage range of 180 degrees and a

coverage area of 600 square feet (56 square meters). The sensor must

have a clear and unobstructed view of the coverage area. Objects blocking

the sensor’s lens may prevent detection thereby causing the light to turn off

even though someone is in the area.

Windows, glass doors, and other

transparent barriers will obstruct the

sensor’s view and prevent detection.

INSTALLATION & WIRING

1. Prepare the switch box.

After the power is turned off at the circuit breaker box, remove the existing wall

plate and mounting screws. Pull the old switch out from the wall box.

2. Identify the type of circuit.

Single Pole

In a Single Pole Circuit (see Figure

2), two single wires connect to two

screws on the existing switch. A

ground wire may also be present

and connected to a ground terminal

on the old switch.

3-Way

In a 3-way circuit (see Figure 3),

there will be [2 runners and

1 common] for both switches

involved.

CAUTION For your safety: Connecting a proper ground to the sensor provides

protection against electrical shock in the event of certain fault conditions. If

a proper ground is not available, consult with a qualified electrician before

continuing installation.

3. Prepare the Wires.

Tag the wires currently connected to

the existing switch, so that they can be

identified later. Disconnect the wires. Make

sure the insulation is stripped off the wires

to expose their copper cores to the length

indicated by the “Strip Gage,” in Figure 3a.

4. Wire the sensor.

1-pole configuration:

Twist existing wires together

with the wire leads on the

R600U sensor as indicated

below. Cap them securely using

the wire nuts provided. See

Figure 4.

• Connect the green or non-

insulated (copper) GROUND

wire from the circuit to the

green ground wire on the

R600U. Make sure there is

a solid ground connection.

• Connect the power wire from

the circuit (HOT) to the black

wire on the R600U.

• Connect the power wire to

the lamp or fan (LOAD) to the red wire on the R600U.

Multilocation configuration (using existing companion 3-way switch):

see Figure 5.

• Connect the green or non-insulated (copper) GROUND wire from the circuit

to the green ground wire on the R600U. Make sure there is a solid ground

connection.

• Connect the power wire from the circuit (HOT) to the black wire on

the R600U.

• Connect the power wire to the lamp or fan (LOAD) to the red wire on

the R600U.

• Connect one of the runner wires to the yellow wire of the R600U.

• For the companion switch, connect the chosen runner wire (presently

hooked up to the yellow wire of the R600U) to the common of the 3-way

companion mechanical switch.

• Connect one of the poles of the companion 3-way switch to ground.

• For the remaining pole of the companion 3-way switch, do not connect to

anything, but still cap off with a wire nut.

Multilocation configuration (using up to 5 units, maximum wire length of

100 ft between companion unit and unit connected to the load):

see Figure 6.

• Connect the green or non-insulated (copper) GROUND wire from the circuit

to the green ground wire on the R600U. Make sure there is a solid ground

connection.

• Connect the power wire from the circuit (HOT) to the black wire on

the R600U.

• Connect the power wire to the lamp or fan (LOAD) to the red wire on

the R600U.

• Connect one of the runner wires to the yellow wire of the R600U.

• For the companion R600U, connect the chosen runner wire (presently

hooked up to the yellow wire of the 1st R600U) to the yellow wire of the

companion R600U.

• Repeat for additional R600U units.

5. Put the R600U in the wall box. Position the lens above the ON/OFF button

(lens at top, button at bottom). Secure it to the wall box with the screws

provided.

6. Make any necessary adjustments. See the SENSOR ADJUSTMENT section

for information.

7. Attach the new cover plate.

8. Restore power to the circuit. Turn on the breaker or replace the fuse.

INITIAL POWER UP DELAY

There is an initial warm-up (about 1 minute) and calibration period the first

time power is applied to the unit and after the load is replaced. The warm-up

sequence also occurs as a result of a power failure, and any time power to the

unit is cycled.

REMOVING FRONT COVER

The wall switch wallplate and front cover

must be removed to gain access to the

adjustment dial under the ON/OFF button.

1. Remove the wallplate.

2. Firmly grasp the edges of the front cover directly below the lens where

it says “open” (see Figure 7). Push in one side first until it pops out, then

the other side. Remove front cover from the unit.

Adjusting the Time Delay

The factory setting for the time delay dial is fully clockwise, providing the

maximum delay of 30 minutes. To reduce the amount of time the load remains

ON, turn the dial counterclockwise (minimum = 30 seconds). The time delay

may be adjusted from 30 seconds to 30 minutes.

CAUTION Do not overturn the time delay adjustment dial.

CHANGING THE COLOR OF THE UNIT

1. Remove the wallplate.

2. Firmly grasp the edges of

the front cover directly below

the lens where it says “open.”

Push in one side first until it

pops out, then the other side.

Remove front cover from the unit

(see Figure 7).

3. Take the new color front cover,

place the top peg in first then

snap in each side one at a

time (see Figure 9).

TROUBLESHOOTING

Status LED is enabled but not blinking and the load will not turn ON:

• Check the circuit breaker to be sure it is functioning.

Load will not turn ON:

Press ON/OFF button. The load should turn ON. If not:

• Check the light bulb and/or motor switch on the fan mechanism.

• Turn OFF power to the circuit then check wire connections.

• For further assistance call 800.223.4185 for technical support.

Load will not turn OFF:

Note: The time delay can be set from 30 seconds to 30 minutes. Ensure that

the time delay is set to the desired delay and that there is no movement within

the sensor’s view for that time period.

• To quickly test the unit for proper operation, turn the time delay to minimum

and move out of the sensor’s view. Lights should turn off after

30 seconds.

• Press the ON/OFF button. If load does not turn off, turn off power to the

circuit then check wire connections.

• For further assistance call 800.223.4185 for technical support.

25'

(7.6m)

12'

(3.7m)

Figure 1: Sensor Coverage Area

Figure 1 : Zone de portée du détecteur

Figura 1: Área de cobertura del sensor

READ AND SAVE THESE INSTRUCTIONS

To be installed by a certified electrician or other qualified person.

WARNING – To prevent severe shock or electrocution, always turn

poweroff at the service panel before installing this product, working on the

circuit, or changing a lamp.

CAUTION

• Do not connect this product to a power source other than 120VAC,

60Hz.

• Use copper wire only.

Specifications

Load..........................................Single Pole or 3 ay

Time Delay ...............................30 Seconds to 30 Minutes

Environment .............................Indoor Use Only

Tools Needed

Insulated Screwdriver, ire Strippers

LIRE ET CONSERVER CES INSTRUCTIONS

Doit être installé par un électricien certifié ou une autre personne qualifiée.

AVERTISSEMENT – Pour éviter tout choc électrique ou une électrocution,

toujours couper l’électricité au niveau du panneau d’alimentation avant

d’installer cette unité, de travailler sur le circuit électrique ou de changer

une lampe.

AVERTISSEMENT

• Ne brancher ce produit qu’à une source d’alimentation de 120 V c.a.,

60 Hz.

• N’utiliser que des fils en cuivre.

Spécifications

Charge ......................................Unipolaire ou à 3 voies

Temporisation ...........................30 secondes à 30 minutes

Environnement ......................... Utilisation en intérieur uniquement

Outils nécessaires

Tournevis isolé, dénudeurs de fil

LEA Y CONSERVE ESTAS INSTRUCCIONES

Para ser instalado por un electricista certificado o persona competente.

ADVERTENCIA – Para evitar descargas eléctricas serias o electrocución,

antes de instalar, trabajar en el circuito o cambiar una lámpara de este

atenuador apague siempre el suministro eléctrico en el panel de servicio.

PRECAUCIÓN

• No conecte este producto a una fuente de alimentación que no sea de

120 V AC, 60Hz.

• Use solamente cables de cobre.

Especificaciones

Carga ........................................Polo único o de 3 vías

Tiempo de demora ...................30 segundos a 30 minutos

Entorno .....................................Solo uso en interiores

Herramientas necesarias

Destornillador aislado, pelacables

Strip Gage

1/2"

12.7mm

Figure 3a: Wire Stripping

Figure 3a : Dénudage des ls

Figura 3a: Pelado de cables

Figure 2:

Single Pole

Figure 2: Pôle simple

Figura 2: Polo único

Line

Ligne

Linea

Black / Noir / Negro

Yellow / Jaune / Amarillo

Green / Vert / Verde

Red

Rouge

Rojo

Load

Charge

Carga

Ground

Terre

Tierra

Neutral

Neutre

Neutro

Figure 4: Single Pole Conguration

Figure 4 : Conguration unipolaire

Figura 4: Conguración del polo único

Figure 6: Multilocation Conguration

Figure 6 : Conguration à plusieurs emplacements

Figura 6: Conguración de ubicación múltiple

Black

Noir

Negro

Yellow / Jaune / Amarillo

Green

Vert

Verde

Ground

Terre

Tierra

Line

Ligne

Linea

Load

Charge

Carga

Line

Ligne

Linea

Red

Rouge

Rojo

Neutral

Neutre

Neutro

Line

Ligne

Linea

Black

Noir

Negro

Green

Vert

Verde

Ground

Terre

Tierra

Red

Rouge

Rojo

Time

Delay

Motion Blink

OFF

30se

c.30min.

5min.

10mi

20mi

11543r1

Figure 7: Remove Front Cover

Figure 7 : Retirez la protection

Figure 7: Desmonte la cubierta

Figure 8: Location of Adjustments

Figure 8 : Emplacement des réglages

Figura 8: Ajustes de localización

Time

Delay

Motion Blink

OFF

30se

c.30min.

5min.

10mi

20mi

11543r1

Figure 9: Replace Front Cover

Figure 9 : Remplacement de

la protection avant

Figura 9: Reemplace la cubierta frontal

common

commun

común

H1 NC

Line

Ligne

Linea

Black

Noir

Negro

Yellow

Jaune

Amarillo

Green

Vert

Verde

Red

Rouge

Rojo

Load

Charge

Carga

Ground

Terre

Tierra

Neutral

Neutre

Neutro

Figure 5: 3-Way Conguration / Figure 5 : Conguration à 3 voies

Figura 5: Conguración de 3 vías

3-Way

In a 3-ay circuit, identify the Common/

Hot wire – connected to the terminal

marked Common or the odd-colored

terminal screw.

Trois voies (3-Way)

Pour un circuit à trois voies, identifier le

câble de commun/courant raccordé à la

borne marquée « Commun » ou à la vis

de borne de couleur différente.

3 vías

En un circuito de 3 vías, identifique el

cable Común/Vivo: conectado al terminal

marcado como Común o al tornillo del

terminal de color diferente.

Figure 3: 3-Way

Figure 3: Trois voies

Figura 3: 3 Vías

RW600U

Time Delay

Dial

Cadran du

délai de la

temporisation

Dial de tiempo

de demora

Strip Gauge,

Borne à vis

Traseros para cables

1/2"

12.7mm

1 2

Summary of Contents

Page 1 - 12'

No: 341002 – 3/13Pass & Seymour®Occupancy/Vacancy Sensor SwitchInterrupteur à détection de présence/Interrupteur détecteur d’inoccupationInterrupt

Page 2 - 1.877.BY.LEGRAND

Comments to this Manuals

No comments

Legrand RW600U User Manual

Browse online or download User Manual for Hardware Legrand RW600U. Legrand RW600U User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Legrand RW600U