Legrand 500 Series Small Raceway Bender Operation User Manual
Browse online or download User Manual for Hardware Legrand 500 Series Small Raceway Bender Operation. Legrand 500 Series Small Raceway Bender Operation User Manual
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
BENDER
USE ARROW
AS YOUR
BENCHMARK.
TOOL
TAKE-UP
TO ARROW
GUIDE FOR OFFSETS
START BENDS AT ARROW ON TOOL
Separate degree scales are provided
for V500 and V700 raceway. Use
closed hook side for V500. Use
open hook side for V700.
Bend until inner edge of
raceway registers with
desired degree
mark.
605 Raceway Cutter for 500 Raceway –
607 Raceway Cutter for 700 Raceway – Portable single action cutters. Case hard steel blades for
clean, fast and easy square cuts every time.
605K Replacement blade for 605 Cutter –
607K Replacement blade for 607 Cutter – Case hard steel blades ensure clean, burr-free cuts.
600B RACEWAY BENDER
OPERATING INSTRUCTIONS
Installation Instruction No.: 28373R1 – Updated April 2004
The 600B consists of: Iron bender, two
sections of 3/4" [19.1mm] galvanized steel
pipe handle and extra-strong coupling.
• Bending with tool in air. Apply hand pressure as close to the tool as possible. Keep pressure
close to the groove for smoother bends and greater accuracy.
• Bending on floor. Work on hard surfaces. Avoid soft sand or deep pile carpets.
• Degree scale. One side of the tool (closed hook side) is scaled for V500 raceway.
The opposite, open hook side, is scaled for V700.
• Zero (0°) degree line. The zero degree line in bottom of groove adjacent to the hook is the
beginning point of the bend.
• Rim notches. The rim notches closest to the hook indicate exact center of a 45° bend.
Numerals “500” and “700” tell which notch to use for which size raceway.
The Raceway at left could be precut to a
49-1/2" [1257mm] length.
10" + 30" + 14" = 54"
[254mm] + [762mm] + [356mm] = [1372mm]
54" less two “GAINS” (4 1/2") = 49 1/2"
[1372mm] less [114mm] = [1257mm]
The “GAIN” on the 600B tool is 2 1/4" [57mm] for
a 90° sweep or 1 1/8" [29mm] for a 45° bend.
BENDING TIPS
BACK-TO-BACK
BENDS
90° STUB LENGTHS
OTHER LABOR SAVING TOOLS FROM WIREMOLD
ANGLE BENDS
BENDER TAKE-UP
90° Stubs
V500 raceway 6" [152mm]
V700 raceway 6" [152mm]
STUB LENGTHS
The “GAIN” is the distance
saved by the arc of a 90° bend.
BENDING WITH THE WIREMOLD 600B BENDER
OFFSET DISTANCE ANGLE WIREMOLD
DEPTH BETWEEN BENDS OF CONDUIT
Inches [mm] Inches [mm] BENDS SHORTENS
3/8" [9.5mm] 2 1/4" [57mm] 10° —
3/4" [19.1mm] 4 1/2" [114mm] 10° —
1" [25mm] 6" [152mm] 10° 1/16"
2" [51mm] 5 1/4" [133mm] 22.5° 3/8"
3" [76mm] 6" [152mm] 30° 3/4"
4" [102mm] 8" [203mm] 30° 1"
5" [127mm] 7" [178mm] 45° 1 7/8"
6" [152mm] 8 1/2" [216mm] 45° 2 1/4"
CAT.
NO.
600B
6"
BENDS V500 AND V700
RACEWAY IN ONE
SWEEP. USE 601B
ADAPTER FOR NO.
V200 RACEWAY.
LOCATE “STAR-POINT”
➤
opposite the finish line
desired – the “star-point”
indicates where back of
the bend will lie.
➞
Knowing the “GAIN” saves time and cuts
waste. Precut raceway to the required length.
10"
14"
30"
10°
22.5°
30°
45°
60°
Measure
to Arrow
Take-Up
Floor Line
The Wiremold Company
U.S. and International:
60 Woodlawn Street • West Hartford, CT 06110
1-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6251
In Canada:
850 Gartshore Street • Fergus, Ontario N1M 2W8
1-800-741-7957 • FAX 519-843-5980
© Copyright 2004 The Wiremold Company All Rights Reserved
28373R1 – Updated April 2004 – For latest specs visit www.wiremold.com
NOTE: on floor bends:
a vertical handle
indicates a 30° bend.
The Back Pusher
The Bender will grab on
in reverse to remove
an overbend.
1
2
Summary of Contents
Page 1 - 600B RACEWAY BENDER
BENDERUSE ARROWAS YOURBENCHMARK.TOOL TAKE-UPTO ARROWGUIDE FOR OFFSETSSTART BENDS AT ARROW ON TOOLSeparate degree scales are providedfor V500 and V700
Page 2 - “3 BEND” PIPE SADDLES
The Simple Box OffsetShrinkage ofAngle Constant Offset Depthof Bends Multiplier Inches [mm]10° x 10° 6.0 1/16" [1.6mm]22.5° x 22.5° 2.6 3/16&quo
Related products and manuals for Hardware Legrand 500 Series Small Raceway Bender Operation
Hardware Legrand V5751-2 User Manual
(1 pages)
(1 pages)
Hardware Legrand V5738 User Manual
(1 pages)
(1 pages)
Hardware Legrand V5738AF User Manual
(1 pages)
(1 pages)
Hardware Legrand V5751 User Manual
(1 pages)
(1 pages)
(2 pages)
Hardware Legrand V5744 User Manual
(1 pages)
(1 pages)
Hardware Legrand G-6012TX User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.318 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals