Legrand DS4000 Obstacle Avoidance User Manual download pdf

DS4000 Obstacle Avoidance

& Offset Fittings

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 43266 – January 2006

Wiremold / Legrand Electrical Systems conform to and should be

installed and properly grounded in compliance with requirements

of the current National Electrical Code, Canadian Electrical

Code, or codes administered by local authorities.

All electrical products may represent possible shock or fire

hazard if improperly installed or used. Wiremold electrical

products are UL listed to U.S. and Canadian safety

standards, made for interior use only, and should be installed

in conformance with current local and/or the National

Electrical Code.

DS4075 INSTALLATION: To jump over small Conduits or Raceways:

Products Covered: DS4075, DS4075A

Existing Obstruction

8" [203mm]

Minimum Spacing

12" [305mm]

Maximum Spacing

DS4000B Raceway Base

Step 2. Install Transition Couplings, tighten set screws to secure.

Step 3. Install Internal Shroud on each side.

Step 1. Install DS4000B on either side of the obstacle. The DS4075 Obstacle Avoidance Fitting can transition over 1/2" and 3/4"

trade size conduit, water pipe, Wiremold 500 Series, 700 Series, 2100 Series, 2000 Series, and 2400 Series Raceways.

For more information, visit www.wiremold.com/ds4000.

Step 4. Install DS4000C Raceway Covers. Step 5. Remove appropriate twistout and secure cover. Push on

until it snaps in place

NOTE: To remove Cover or install a Tamper Resistance Kit, refer to page 6 of this instruction sheet.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - & Offset Fittings

DS4000 Obstacle Avoidance& Offset FittingsINSTALLATION INSTRUCTIONSInstallation Instruction No.: 43266 – January 2006Wiremold / Legrand Electric

Page 2

2To use the DS4075 as a transition to Wiremold 500 Series or 700 Series Raceway:Step 1. Install 500/700 Adapter into the opening with suppliedscrews.

Page 3

3To use the DS4075 as a transition to Wiremold 2400 or 2400BD Series Raceway:Step 1. Install DS4075 as before. Install 2400 Adapter in onechannel for

Page 4

4DS4075A OFFSET FITTING INSTALLATION:Step 1. Measure the offset.Step 3. Mount to Wall with #8 minimum Fasteners. TightenSet Screws as Shown.Step 2. Tr

Page 5

5Step 5. Measure Cover distance from top of Divider.Step 7. Snap on Cover. Step 8. Install Elbow Cover and Inside Corner Trim.MeasureStep 6. Trim Cove

Page 6

6Cover Removal w/650RTFITTING COVER REMOVAL – Fitting Cover can be removed using two methods:Cover Removal w/ScrewdriverStep 1. Locate Dimple on Fitti

Page 7

7NOTES

Page 8

Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6

Comments to this Manuals

No comments

Legrand DS4000 Obstacle Avoidance User Manual

Browse online or download User Manual for Hardware Legrand DS4000 Obstacle Avoidance. Legrand DS4000 Obstacle Avoidance User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Legrand DS4000 Obstacle Avoidance