Legrand ALDS4000 Designer Series Large Raceway User Manual download pdf

DS4000/ALDS4000

Prewired Raceway

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 43619 – July 2006

Wiremold / Legrand Electrical Systems conform to and should be

installed and properly grounded in compliance with requirements

of the current National Electrical Code, Canadian Electrical

Code, or codes administered by local authorities.

All electrical products may represent possible shock or fire

hazard if improperly installed or used. Wiremold electrical

products are UL listed to U.S. and Canadian safety

standards, made for interior use only, and should be installed

in conformance with current local and/or the National

Electrical Code.

For more information, visit www.wiremold.com/ds4000.

Step 1. If the installation requires Fittings,

start at an appropriate location

such as a corner. Refer to specific

fitting installation instructions for

proper mounting.

Step 2. Leaving Couplings loose, slide

DS4000 Base section onto

installed Adjust-to-Fit

™

Couplings until Base Section

butts against Fitting. Tighten

Coupling Screws. Secure Base

Section to the wall using #8

Fasteners spaced 48"

[1.2m] apart

Note: ALDS4000 Base is not

provided with mounting

holes. Drill a hole at

desired mounting location

or use self-drilling screws.

Step 3. Butt succeeding DS4000 Base Sections

tightly to installed base in order to

maintain hole alignment. Slide Couplings

into place and tighten.

Adjust-to-Fit™

Couplings

Note: Wires have been removed for clarity.

Step 4. Raceway can be fed using several methods.

1. Use DS40410A/ALDS4010A Entrance End Fitting. (See specific installation instructions.)

2. Use DS4010B Blank End Fitting. (See specific installation instructions.)

3. Drill a hole into Base Section for 1/2", 3/4", or 1" trade size conduit.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Prewired Raceway

DS4000/ALDS4000Prewired RacewayINSTALLATION INSTRUCTIONSInstallation Instruction No.: 43619 – July 2006Wiremold / Legrand Electrical Systems conform

Page 2 - Hook Cover into Base Section

2Step 5. Use the #10-32 hole in the Coupling toground the system where it is fed.Step 6. Make wiring connections betweenraceway sections using connect

Page 3 - DS4006 Seam Clip

3Snap Activation Plate onto Raceway Base.SqueezeFirstInstallation complete. (DS4047R shown.)Install Device Plate first. Insert and tighten Screw then

Page 4

4CABLE CATEGORY/ O.D. 40% FILL 1/240% FILL w/DOWNWARDTYPE DESIGNATION Inches [mm]COMPARTMENT ACTIVATION/CROSSOVERUNSHIELDED 4-pair, 24 AWG Cat 3 0

Page 5

5CABLE CATEGORY/ O.D. 40% FILL 1/2TYPE DESIGNATION Inches [mm]COMPARTMENTUNSHIELDED 4-pair, 24 AWG Cat 3 0.190 [4.8] 68TWISTED PAIR 4-pair, 24 AW

Page 6

Page 7

Page 8

8Wiremold / LegrandU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-

Comments to this Manuals

No comments

Legrand ALDS4000 Designer Series Large Raceway User Manual

Browse online or download User Manual for Hardware Legrand ALDS4000 Designer Series Large Raceway. Legrand ALDS4000 Designer Series Large Raceway User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Legrand ALDS4000 Designer Series Large Raceway