Legrand CRFB Series Floor Box User Manual download pdf

CRFB Series Floor Box

I N S T A L L A T I O N I N S T R U C T I O N S

Installation Instruction No.: 1 009 621 – September 2010

Legrand/Wiremold electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Legrand/Wiremold electrical

products may bear the mark of a Nationally Recognized Testing

Laboratory (NRTL) and should be installed in conformance with current

local and/or the National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

1. Prior to installation, an 8-3/8 ± 1/8 in. [213 ± 3 mm]

diameter hole must be cut or preformed into the raised

floor panel or wood floor. If knockouts on sides of box

are to be used, proceed to steps 4 and 5. Pull cable and

conduit through opening prior to termination.

2. If necessary, use bushing(s) and wire tunnel to facilitate

wire and cable routing. Remove the temporary cover and

the (5) #8 hex screws securing the device mounting plate

and lift it out of the box, exposing the internal barriers.

Remove necessary knockouts and twistouts between

compartments to allow desired wiring layout. Replace the

internal barriers and reinstall the device mounting plate

back in its original orientation.

3. Attach flexible conduit and fittings to the steel box body.

Terminate wiring devices in compliance with the NEC

and local codes. Cover each compartment with the

Device Plate that matches both the Location and Type

of Device used.

PRODUCTS COVERED: CRFB4, CRFBBTC, CRFBCTC, CRFB-X-1, CRFB-X-2, CRFB-X-3 AND CRFB-X-4.

Also 8ATC and 8CT Covers when installed on CRFB Series Floor Boxes.

3/8" ± 1/8"

[

213 ± 3mm]

emporary

Cover

#8 Hex

Screw

Bushing

Right

Barrier

Device Mounting

Plate

Center Barrier

(with KO removed)

Left

Barrier

Wire

Tunnel

Device

Location #1

Device

Location #3

Device

Location #4

Device

Location #2

NOTE: Floor thickness range (including floor

covering 3/8" – 2" [9.5mm – 51mm].

1 2 3 4

Summary of Contents

Page 1 - CRFB Series Floor Box

CRFB Series Floor BoxI N S T A L L A T I O N I N S T R U C T I O N SInstallation Instruction No.: 1 009 621 – September 2010Legrand/Wiremold elect

Page 2

5. Tighten mounting screw until steel anchor is adjustedsecurely below floor.6. Install the floor covering prior to attaching the cover.For carpet ins

Page 3

9. 8CT and 8CTC COVERS: Open the lid and insert CoverAttachment Screws through Sealing Washers and attachCover Flange to CRFB4 Box.AttachmentScrewSea

Page 4 - CRFB Cutting Template

WIREMOLDU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-233-6251 Canad

Related models: CRFB | CRFB-SR1-1 | CRFB-SR2-2 | CRFB-SR1-3 | CRFB-SR1-2 | CRFB-B-1 | CRFB-B-2 | CRFB-B-3 | CRFB-SR1-4 | CRFB-BEZ6A-4 | CRFB-B-4 | CRFB-6COM-4 | CRFB-D-4 | CRFB-GFI-4 | CRFB-AB-3 | CRFB-AB-1 | CRFB-RT-1 |

Comments to this Manuals

No comments

Legrand CRFB Series Floor Box User Manual

Browse online or download User Manual for Hardware Legrand CRFB Series Floor Box. Legrand CRFB Series Floor Box User Manual

Summary of Contents

Related models: CRFB | CRFB-SR1-1 | CRFB-SR2-2 | CRFB-SR1-3 | CRFB-SR1-2 | CRFB-B-1 | CRFB-B-2 | CRFB-B-3 | CRFB-SR1-4 | CRFB-BEZ6A-4 | CRFB-B-4 | CRFB-6COM-4 | CRFB-D-4 | CRFB-GFI-4 | CRFB-AB-3 | CRFB-AB-1 | CRFB-RT-1 |

Comments to this Manuals

Related products and manuals for Hardware Legrand CRFB Series Floor Box