Legrand HLV703PTC User Manual download pdf

P.O. Box 4822, Syracuse, NY 13221-4822

(800-223-4185)

www.passandseymour.com P/N 340805 Rev. B

HARMONY

™

MAGNETIC LOW VOLTAGE DIMMERS

INSTALLATION INSTRUCTIONS

P/N 340805 Rev. B

NOTE: This device should be installed after sheet rocking and painting are

completed.

NOTE: It is normal for the dimmer to feel warm during operation. Use a

separate neutral wire for each phase of a multiphase system containing a

dimmer, and for high power single phase applications where flickering is

present.

MULTIPLE GANGING OF DIMMERS AND OTHER DEVICE

Any combination of dimmer models and other devices may be ganged

together. Break off tabs are provided on the 1100VA dimmer straps for multi-

gang applications. Pry off the tabs using pliers before installation, as shown

in the figure. De-rate the maximum load according to the following table:

Figure: Multiple Ganging of Devices

Figura: Instalación en grupo de múltiples dispositivos

Figure : Groupement de plusieurs dispositifs

IMPORTANT NOTES:

1. All dimmers can be damaged by improper wiring. Check for short circuits

prior to installing the dimmer.

Procedure for short circuit check:

a. Disconnect power to circuit by removing fuse or turn circuit breakers OFF.

b. Install a switch instead of the dimmer. Turn the switch to the “ON”

position.

c. Turn power ON. If the circuit breaker trips, a short is present. If the light

fails to turn ON and OFF with the switch, the wiring may be incorrect.

d. Correct wiring, if necessary and retest.

e. Install the dimmer only after the light operates properly with the switch.

2. Protect from dirt and dust. The dimmer can be damaged from contam-

inates encountered during the construction process. If lighting is required

prior to the construction process completion, then a switch should be

temporarily installed in place of the dimmer. The dimmer should not be

installed until the construction process is complete.

Any dimmer damaged due to improper installation is not covered under

warranty.

WARRANTIES

Lifetime Warranty. The device you have purchased is warranted under normal use

against defects in workmanship and materials for as long as you own the device. If the

device fails due to manufacturing defect during normal use, return the device for

replacement to the store where purchased or send to:

Pass & Seymour Legrand

50 Boyd Avenue

Syracuse, NY 13209

All requests for replacement must include a dated sales receipt (legible copies

acceptable).

ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO A

PERIOD OF TWO YEARS FROM THE DATE OF PURCHASE. YOUR SOLE AND EXCLUSIVE

REMEDY AGAINST PASS & SEYMOUR LEGRAND UNDER ANY WARRANTY SHALL BE THE

EQUIVALENT REPLACEMENT OF THE DEVICE. IN NO EVENT SHALL ANY WARRANTY

APPLY TO ANY DEFECT ARISING OUT OF ANY ALTERATION OF THE DEVICE, IMPROPER

WIRING, IMPROPER INSTALLATION, MISUSE, ABNORMAL USE OR NEGLIGENCE. IN NO

EVENT SHALL PASS & SEYMOUR LEGRAND BE LIABLE FOR LOST PROFITS, INDIRECT,

SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do

not allow limitations on how long implied warranties last and do not allow exclusion or

limitation of incidental or consequential damages. Some of the above limitations or

exclusions may not apply to every purchaser.

Remove all fins

Retirar todas

las lengüetas

Retirer toutes

les ailettes

Remove inside fins only

Retirar lengüetas internas

solamente

Retirer les ailettes

intérieures uniquement

Dimmer Maximum

Multi-Gang Derating

Catalog # Load 2 Gang Installation 3 Gang Installation

DLV703P 700VA 700VA 650VA

DLV1103P 1100VA 900VA 700VA

READ AND SAVE THESE INSTRUCTIONS

To be installed by a certified electrician or other qualified person.

These Dimmers are for use with Magnetic Low Voltage Incandescent and

Halogen lamps.

WARNING – To prevent severe shock or electrocution, always turn power off

at the service panel before installing this unit, working on the circuit, or

changing a lamp.

Caution – To reduce the risk of overheating and possible damage to other

equipment, do not install to control a receptacle, a fluorescent light or bulb or

a motor-operated appliance. The maximum VA rating of this dimmer applies

to the transformer input, not the load on the transformer secondary.

• Do not use with inoperative or missing lamps. Use of this dimmer with

inoperative or missing lamps can create an over current condition which

may damage the transformer. Use transformers that incorporate thermal

protection of a fuse at the primary windings.

• Connect only in a 120VAC, 60Hz circuit to control the primary of a

transformer supplied incandescent.

• A 50VA minimum load is required.

• Use copper wire only.

Directions

1. Disconnect power to circuit by removing fuse or turn circuit breakers OFF

before installing.

2. Remove wall plate and switch mounting screws, pull existing switch from

wall box.

3. Disconnect existing switch from circuit. 3-way installation: Identify the

“Common” wire (wire connected to the terminal marked common or odd

colored terminal). For new installation identify wire connected to power

source or to the load.

4. Connect dimmer as shown in the installation diagram using #12 or #14

AWG stranded or solid copper conductors. Strip wire using gauge on back

of device.

INSTALLATION DIAGRAM FOR DIMMERS

DIAGRAMA DE INSTALACIÓN PARA ATENUADORES

SCHÉMA D’INSTALLATION DES GRADATEURS

Single Pole/Unipolar/Unipolaire 3-Way/3 vías/3 voies

Screw Pressure Plate Back Wire

Cable trasero con tornillo y placa de presión

Fil arrière avec vis et plaque de pression

5. Install dimmer in wall box, with word “TOP” on the strap right side up, using

mounting screws provided.

6. Attach wall plate and then restore power to circuit.

7. Dimmer may need to be adjusted to accommodate low voltage transformer.

To do this, DISCONNECT POWER FROM CIRCUIT, and remove the

Wallplate. Use a small insulated, flat tipped screwdriver to adjust the trim

pot, which is accessible via the slot (marked “CALIBRATION”) provided on

the strap. Turn down to increase the minimum light intensity setting. Next,

mount the Wallplate back, restore the power and test. Repeat above as

necessary. Note: Never adjust trim pot when circuit is live.

12192_HarmonyMagDim_IS_340805 1/5/07 8:44 AM Page 2

1 2

Summary of Contents

Page 1 - MAGNETIC LOW VOLTAGE DIMMERS

P.O. Box 4822, Syracuse, NY 13221-4822(800-223-4185)www.passandseymour.com P/N 340805 Rev. BHARMONY™MAGNETIC LOW VOLTAGE DIMMERSINSTALLATION INSTRUCTI

Page 2 - TENSION HARMONY

LEA Y CONSERVE ESTAS INSTRUCCIONESPara ser instalado por un electricista certificado o persona competente.Estos atenuadores son para uso con lámparas

Related models: HLV1103PTC | HLV703PW | HLV1103PW | TDLV1103PBK | TDLV703PBK | TDLV1103P | TDLV703P | TDLV1103PI | TDLV703PI | TDLV1103PLA | TDLV703PLA | TDLV703PW | TDLV1103PW | TDFB83P | TD703P | H4FBL3P |

Comments to this Manuals

No comments

Legrand HLV703PTC User Manual

Browse online or download User Manual for Hardware Legrand HLV703PTC. Legrand HLV703PTC User Manual

Summary of Contents

Related models: HLV1103PTC | HLV703PW | HLV1103PW | TDLV1103PBK | TDLV703PBK | TDLV1103P | TDLV703P | TDLV1103PI | TDLV703PI | TDLV1103PLA | TDLV703PLA | TDLV703PW | TDLV1103PW | TDFB83P | TD703P | H4FBL3P |

Comments to this Manuals

Related products and manuals for Hardware Legrand HLV703PTC