Legrand Convia Enabled Walkerflex System User Manual download pdf

Convia

Enabled

Walkerflex

System

I N S T A L L A T I O N I N S T R U C T I O N S

Installation Instruction No.: 1 008 478 – August 2009

Wiremold electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Wiremold electrical products

may bear the mark as UL Listed and/or Classified and

should be installed in conformance with current local and/or the

National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

roducts Covered: NVHUB, LVHUB, NRD1, NRD2, LRD1, LRD2, NPM12, NPM22, NPM24, NPM44, NPM24PF,

NPM44PF, CNDU, CLDU, CNWC, CLWC, CNPA, CLPA, CNCS, CLCS, CNCBS, CLCBS, CNCW,

CLCW, CAP3456 & CAP810

NOTE: Label on product indicates which products are suitable for use in air handing spaces

in accordance with Sec. 300-22(C) of the National Electric Code.

1. Each Convia

Enabled Walkerflex

System connector

contains a color coded key that indicates rating, conductor

location and orientation. Only like colored keys can be

mated. See Key Configuration and Color Chart on page 11

for available options. Each key is comprised of one or more

configurations.

2. Disconnect power from source prior to wiring any Walkerflex

component into the building’s electrical power system.

3. Installer to determine the maximum power cable length

based on wire gauge and circuit load.

4. Installer to ensure adequate overload protection based on

the system key, rating and circuit load.

5. Refer to appropriate Wiring Diagram and System Key

Configuration Conductor Location Chart for field connections

of Cat. Nos. CNWC/CLWC (Wire Connector) and

CNCW/CLCW (Cable Whips). Refer to wiring diagram

supplied with CNDU/CLDU (Distribution Unit) for field

termination.

6. Securing and Supporting of Cables and Components: Refer

to NEC Article 604, Manufacturing Wiring Systems and any

local codes.

7. Cap all unused connector openings with Cat. No. CAP3456

(for 3 through 6 wire system) or Cat. No. CAP810 (for 8 and

10 wire system).

8. All Convia Enabled accessories are available in a 3-6 wire

and 8-10 wire system and are rated 20A, 120V.

9. 277V Convia Enabled Walkerflex components are only

available in 3-6 wire configurations.

10.The Convia Enabled Walkerflex system is compatible with

the standard Walkerflex system of the same configuration

and key.

GENERAL INFORMATION

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - Walkerflex

Convia®EnabledWalkerflex®System I N S T A L L A T I O N I N S T R U C T I O N SInstallation Instruction No.: 1 008 478 – August 2009Wiremold elect

Page 2

10WALKERFLEX SYSTEM WIRING DIAGRAMS (continued)120V 20A SYSTEM FOR 4 LINE CONDUCTORS & 2NEUTRALS CONNECTED TO AN ISOLATED GROUNDTHREE-PHASE WYE120

Page 3 - Network Hubs

11TERMINALBLOCK SYSTEM COLOR KEY POWER OUT POWER IN20A, Black 422120V,4H/2N/IG20A, Orange 442120V, 4H/4N/IG20A, Natural 332120V, 3H/3N/IG20A, Blue

Page 4 - Relay Dimmer

WIREMOLDU.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-233-6251 Canad

Page 5

2CNDU and CLDU Module & Flex Cables: The CNDU and CLDU (CLDU is available for 3-6 wire configurations only) module is the main power source and

Page 6 - Power Modules

3CONVIA ENABLE WALKERFLEX SYSTEM INSTALLATION (continued)Network HubsThe Network Hub module makes up thebackbone or Main Bus of the network. MultipleN

Page 7 - IR Sensor

4CONVIA ENABLE WALKERFLEX SYSTEM INSTALLATION (continued)Relay DimmerThe Relay Dimmer Modules are used tocontrol lighting and other devices, (maximum2

Page 8 - ALKERFLEX SYSTEM ACCESSORIES

5CONVIA ENABLE WALKERFLEX SYSTEM INSTALLATION (continued)Step 3: Connect Wiremold Convia Enabled Pre-terminatedRJ45 cables between the Network Hub and

Page 9 - L1 Black

6CONVIA ENABLE WALKERFLEX SYSTEM INSTALLATION (continued)Power ModulesThe Power Modules are used to controlgeneral purpose loads, (maximum 20A load)vi

Page 10 - (continued)

7For Field Wired Units: Connect conduit to appropriate conduit opening and wire per the NationalElectric Code. (See Wiring Schematic below or on produ

Page 11

8Access Floor BoxTYPICAL PREWIRED ACCESS FLOOR BOX INSTALLATIONSCat. No. CNCS(Cable Set)Cat. No. CNCS(Cable Set)Cat. No. CNCW(Cable Whip)Cat. No. CNPA

Page 12

9120V 20A SYSTEM FOR 1, 2, 3 OR 4 LINE CONDUCTORSCONNECTED TO A GROUNDED THREE-PHASE WYE120V 20A SYSTEM FOR 1 OR 2 LINE CONDUCTORSCONNECTED TO A DUAL

Comments to this Manuals

No comments

Legrand Convia Enabled Walkerflex System User Manual

Browse online or download User Manual for Hardware Legrand Convia Enabled Walkerflex System. Legrand Convia Enabled Walkerflex System User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Legrand Convia Enabled Walkerflex System